Lorena Mid Gain Overdrive

Lorena is our approach on putting the perfect Klon out there and we did a good job. Using almost all the original components, we were able to make this pedal as close to the original as possible.

Lorena sounds great with just about any amp/guitar combination as it is very transparent and just fine tuning the sound you already love. The character of your amp will not be changed.

Its internal 9V to 18V conversion doubles the headroom and opens up a whole new world of overdriven sounds.

Controls

Drive

Controls the amount of drive from clean to mid gain. We use a dual gang potentiometer to blend between a clean boost and a diode clipped distortion.

Volume

Controls the overall volume

Tone

Tone shaping knob, controlling mid and high frequencies

Features

 • True bypass or high quality buffered bypass (setup switch inside)

 • Internal 9V to 18V conversion for more headroom

 • Neutrik jacks for durability

 • High quality 24AWG solid wiring

 • No battery support

 • Standard 9V negative center DC input

 • Current consumption at 9V DC: 15mA

 

Solana Mid Gain Overdrive

Solana is a very transparent overdrive based on a Bluesbreaker design.
Offering a lot of headroom and gain along with a very versatile tone control and a high cut switch, this pedal allows you to find the perfect sound for your rig. It is suitable for both Strat and Les Paul type guitars and adds just the right touch to your sound.
Solana offers enough clean headroom to be used as a clean boost.

Controls

Drive

Controls the amount of gain from clean to almost distorted

Volume

Controls the overall volume

Tone

Adds or cuts high frequencies. Low frequencies are not affected

High Cut (Toggle Switch)

Acts as a brightness cut

Features

 • True bypass wiring

 • Neutrik jacks for durability

 • High quality 24AWG solid wiring

 • No battery support

 • Standard 9V negative center DC input

 • Current consumption at 9V DC: 10mA

Yara Optical Compressor

Yara is a very versatile low noise Compressor, designed to meet the high standards of guitar compression.

Two modes, accessible by a toggle switch, offer a lot of options for tone-shaping. Sustain mode (down position) delivers a very dynamic and touch sensitive tone with the ability for long sustain, whereas the compression mode (up position) offers the standard features of a compressor with a range from light to heavy compression.

Controls

Compression

Controls the amount of compression or sustain. Less touch sensitive response at higher

Level

Controls the level of the sustained signal in sustain mode whereas in compression mode the overall volume is being affected

Tone

Finetunes the compressed sound. Full range compression, when turned all the way down, less bottom at middle position and less treble when turned all the way up

Sustain/Compressor

Toggle switch to enter either compression or sustain mode

Features

 • True bypass wiring

• Neutrik jacks for durability

• High quality 24AWG solid wiring

• No battery support

• Standard 9V negative center DC input

• Current consumption at 9V DC: 15mA

Valve A/B Input Regulator

This pedal takes care of a very common problem when running your rig with two guitars: uneven guitar signals.

Valve allows you to adjust the volume of channel B to channel A with the help of a clean boost, offering two equal signals that will run through your board. No more adjusting your pedals to different signal strengths.

In addition, a buffered splitter provides the perfect input impedance to your rig, providing a clear sound, no matter how many pedals you're using, and an additional tuner out to take your tuner out of the chain. The tuner out can also be used to run stereo signals.

Controls

3PDT-Switch:

Changes between channel A and B

Volume

Adjusts output of channel B to match the volume of channel A

Features

• Neutrik jacks for durability 
• High quality 24AWG solid wiring 
• No battery support 
• Standard 9V negative center DC input 
• Current consumption at 9V DC: 20mA

Detonator Booster

Detonator is a simple clean boost, that pushes your signal up to 25db, with an additional tone control for more versatility

Controls

Level

Controls the amount of gain. No gain added when fully CCW

Tone

Adds bass and cuts treble when turned CCW, adds treble and cuts bass when turned CW. Neutral at 12 o'clock position

Features

• True bypass wiring

• Neutrik jacks for durability

• High quality 24AWG solid wiring

• No battery support

• Standard 9V negative center DC input

• Current consumption at 9V DC: 5mA

Hatchet Signal Splitter

Hatchet is a signal splitter. It provides two buffered outputs either for stereo rigs or to separate your tuner. Can be used anywhere on your board.

Controls

Level

Controls the amount of gain. No gain added when fully CCW

Tone

Adds bass and cuts treble when turned CCW, adds treble and cuts bass when turned CW. Neutral at 12 o'clock position

Features

• Neutrik jacks for durability

• High quality 24AWG solid wiring

• No battery support

• Standard 9V negative center DC input

• Current consumption at 9V DC: 2mA

Plunger Mono Muffer

Using too many pedals can lead to tone loss, if you don't use a Buffer. Especially high frequencies get stuck somewhere in between all those cables. That's when the Plunger steps in. Placed at the beginning of your chain, it converts a high impedance signal into a low impedance one, creating a strong and clear signal, ready for as many pedals as you like.

Features

 • Neutrik jacks for durability

 • High quality 24AWG solid wiring

 • No battery support

 • Standard 9V negative center DC input

 • Current consumption at 9V DC: 2mA

Double Plunger Stereo Buffer

The Double Plunger. Same as the Plunger. Just in Stereo

Using too many pedals can lead to tone loss, if you don't use a Buffer. Especially high frequencies get stuck somewhere in between all those cables. That's when the Plunger steps in. Placed at the beginning of your chain, it converts a high impedance signal into a low impedance one, creating a strong and clear signal, ready for as many pedals as you like.

Features

 • Neutrik jacks for durability

 • High quality 24AWG solid wiring

 • No battery support

 • Standard 9V negative center DC input

 • Current consumption at 9V DC: 2mA

Ink Pot Expression Pedal

Expression Pedal for remote control of Timeline, Boss and many more pedals with an expression jack.

Available in white, vintage blue and vintage green

Features

• Neutrik jacks for durability

• High quality 24AWG solid wiring

Double Ink Pot Double Expression Pedal

Double Expression Pedal for Strymon, Boss and many more units. Saves a lot of space on your board and allows you to control two pedals.

Features

• Neutrik jacks for durability

• High quality 24AWG solid wiring

Tap Tempo

External Tap Tempo for pedals with an tap input jack

Available in white, vintage blue and vintage green

Features

 • Neutrik jacks for durability

 • High quality 24AWG solid wiring

EM-Drive Transparent Overdrive

Handwired, Handbuilt in Broken Arrow, Oklahoma USA using some of the finest quality & reliable parts available. This pedal does everything from a slight boost/sparkle to a nice, warm light OD sound. Good for use as a first stage OD or a nice boost pedal.... you may find yourself leaving this on the entire gig!

Specs

• USA Made Custom Potentiometers (for an excellent taper and feel)
• Handwired Construction
• Blue LED
• Durable Powdercoated Finish
• USA Switchcraft Jacks
• Quality 3PDT True Bypass Footswitch
• Hand picked and matched parts for ultimate tone.
• Each & Every Pedal is Handbuilt, wired and tested in Broken Arrow, Oklahoma USA
• Power: Standard 9-18V volt DC power supply with a negative center 2.1mm barrel, NO internal battery option.
• Current Draw: 14mA

We highly recommend a quality power supply that utilizes isolated power. This would include the Voodoo Lab PP2+ or the IS0-5 and several other brands/models.

Includes full warranty against defects in components or manufacturing. We do not have a return policy for non-defective pedals, so if that is important to you please purchase a standard unit through one of our authorized dealers. Thank you for your interest in Emerson Custom Guitars!

Paramount Overdrive

Handwired, Handbuilt in Broken Arrow, Oklahoma USA using some of the finest quality materials available.

The Paramount Overdrive is a Medium Gain (Second Stage Overdrive) that stacks very well with almost any pedal. It can be ran at 9-18v (18v for more headroom). The Paramount is an original Emerson circuit that is powerful has plenty of usable gain on tap to fit most any situation. The Paramount's character is refreshingly unique yet sits in the mix very well and has a familiar sound. This pedal is very dynamic and responds well to pick attack and the subtle nuances of the player.

Specs

• USA Made Custom Potentiometers (for an excellent taper and feel)
• Handwired Construction
• Blue LED
• Durable Powdercoated Finish
• USA Switchcraft Jacks
• 3PDT True Bypass Footswitch
• Hand picked and matched parts for ultimate tone.
• Each & Every Pedal is Handbuilt, wired and tested in Broken Arrow, Oklahoma USA
• Power: Standard 9-18V volt DC power supply with a negative center 2.1mm barrel, NO internal battery option.
• Current Draw: 10mA

We highly recommend a quality power supply that utilizes isolated power. This would include the Voodoo Lab PP2+ or the IS0-5 and several other brands/models.

Includes full warranty against defects in components or manufacturing. Please see our Warranty Page.

Please Note: We DO NOT accept returns, nor offer refunds, or exchanges. If this is important to you please purchase a standard unit through one of our authorized dealers who offers a return/refund/echange policy. Thank you for your interest in Emerson Custom Guitars!

Concord Utility Buffer

Handbuilt in Broken Arrow, Oklahoma USA using premium audio grade components to provide ultimate clarity and signal response. This utility pedal "buffers" your signal to bring back the clarity and high end sparkle of your input signal that is lost when you use a lot of pedals and/or have lots of cable between your guitar or bass, and your amp. This pedal is a tool that once you have on your rig you'll never wanna be without it.

Placement:
We recommend placing the Concord Buffer as the first device in your signal chain. If you are using a vintage fuzz pedal such as a Fuzz Face® or Tone Bender® we recommend placing the Concord after those devices to retain their character and relationship with your instrument's electronics.

Specs

•  "Always on" (No on/off switch)
•  Blue LED
•  Durable Vintage Orange Sparkle Powdercoated Finish
•  Side Mounted Audio & Power Jacks to save space
•  Premium Audio Grade Capacitors & Components used throughout
•  Each & Every Pedal is Handbuilt, wired and tested in Broken Arrow, Oklahoma USA
• Power: Standard 9v volt DC power supply with a negative center 2.1mm barrel, NO internal battery option.
•  Dimensions (includes jacks): 3.7" Long x 1.7" Wide x 1.3" Tall
• Current Draw: 10mA

We highly recommend a quality power supply that utilizes isolated power. This would include the Voodoo Lab PP2+ or the IS0-5 and several other brands/models.

Includes full warranty against defects in components or manufacturing. We do not have a return policy for non-defective pedals, so if that is important to you please purchase a standard unit through one of our authorized dealers. Thank you for your interest in Emerson Custom Guitars!